ISO 9001 CERTIFIED  ·  CONSULTANT APPROVED  ·  EXPORTING SINCE 2005
When the fan curve lies: system resistance explained
RESOURCES  /  ENGINEERING NOTES  /  BLOWERS · 5 MIN READ

When the fan curve lies: system resistance explained

A blower runs where its curve meets the system, not where the data sheet says. Here is why that gap costs airflow and power.

BY THE BHAVI PLAST ENGINEERING TEAM

A blower never delivers its catalogue rating. It delivers whatever flow it lands on where its own performance curve meets the resistance of the system it is bolted into. Pick the fan without knowing that resistance, and the number on the data sheet is a promise the system was never going to keep.

The curve doesn't really lie. It just answers a different question from the one you asked.

Two curves, one operating point

Every fan has a performance curve: at a fixed speed, how much pressure it can develop at each flow rate. As you ask for more flow, the pressure it can push against falls. The catalogue rating is just one point on that curve.

Every exhaust system has a system curve: how much pressure it takes to move air through it at each flow rate. That resistance comes from everything in the path — the capture hoods, every metre of duct, each bend, damper and transition, the scrubber bed, the mist eliminator, the stack, and the losses where air enters and leaves.

System resistance rises with the square of flow:

ΔP = k × Q2

Double the airflow and the resistance roughly quadruples. The fan runs exactly where the two curves cross. Not where you hoped — where they cross.

What happens when the resistance is guessed

Suppose a scrubber system is designed for 30,000 m³/h at 200 mmWC, and a backward-curved fan is selected for exactly that point. In reality the scrubber's bed is a little deeper, there are two more bends than the layout showed, and the stack has a rain cap. The true resistance at 30,000 m³/h is 250 mmWC — a quarter higher than assumed.

The fan doesn't deliver 30,000 m³/h against the extra resistance. It slides back along its curve to a new crossing point. For a typical backward-curved curve, that is somewhere around 28,000 m³/h — about 6% less air.

Six per cent sounds harmless. But every hood in the plant now draws about 6% less, and capture velocity at the far end of the duct network — already the weakest point — drops below what's needed to contain the fume. Operators notice smell at one tank, and nobody connects it to a fan selection made months earlier.

The opposite error is just as real. Overestimate the resistance, and the fan delivers more air than intended. Gas velocity through the scrubber rises, the bed approaches flooding, liquor is carried into the stack, and the motor draws more power than anyone budgeted for.

Why you can't just speed it up afterwards

The instinctive fix for too little air is to run the fan faster. The fan laws explain why that is expensive:

  • Flow rises in proportion to speed
  • Pressure rises with the square of speed
  • Power rises with the cube of speed

Clawing back that 6% of flow means running about 6% faster — and that costs roughly 19% more power, since 1.06³ ≈ 1.19. If the motor was selected with little margin, it won't have that to give. The fix becomes a new motor, sometimes a new fan.

Two corrections that get forgotten

Gas density. Catalogue curves are drawn for standard air, at around 20 °C and 1.2 kg/m³. Hot or humid gas is lighter, and a fan develops less pressure in direct proportion to the density of what it is moving. Saturated exhaust at 60 °C can be 12 to 17% lighter than standard air — so a fan chosen on the standard curve falls short by roughly the same margin, before a single duct is counted.

System effect. A curve is measured on a test rig with smooth, straight ducts on either side. Bolt an elbow directly onto the fan inlet, or discharge it straight into a sharp bend, and the air reaches the impeller swirling and uneven. The fan performs below its curve. Good layouts give the fan a few duct diameters of straight run at the inlet wherever possible.

Where the operating point should sit

A well-chosen fan operates near the peak of its efficiency, on the stable part of its curve. Backward-curved designs are preferred for exhaust and scrubber duty partly because their power curve peaks and then falls — they are non-overloading, so the motor can't be driven beyond its rating by a change in the system.

Run any fan too far to the left of its curve — low flow, high pressure — and it can become unstable. Airflow pulses, noise and vibration rise, and bearings wear faster. That usually signals a fan chosen well oversized for the system it serves.

How to get it right

  1. Calculate the system resistance properly, element by element, using an established method such as the ACGIH industrial ventilation approach — hoods, ducts, fittings, scrubber, mist eliminator and stack.
  2. Correct for the real gas: its temperature, moisture and density, at the fan.
  3. Add a sensible margin, and state it, rather than burying an unknown one in the selection.
  4. Select from a tested performance curve, not a catalogue table, with the duty point near peak efficiency.
  5. Leave room to adjust: a variable frequency drive, or at least a damper, so the system can be balanced at commissioning.
  6. Measure at commissioning: airflow at each hood, and pressure across the fan, compared against the design.

This is why we design the blower and the scrubber together, as one system. Our in-house fan software generates the performance curve for each selection, and every blower is performance-tested to IS 4894 before despatch, so the curve we design against is one we have actually measured.

If an existing system isn't pulling the air it should, the fan is often the first thing blamed and the last thing at fault. Send us the layout and a few pressure readings, and we can usually tell you where the resistance went.

HAVE A DUTY LIKE THIS?
Send us the process data. We'll come back with a sized proposal.
Start an enquiry
KEEP READING
More engineering notes
All resources →
ENQUIRY

Pick the equipment. We will send you the data sheet.

Choose the equipment you need. We will take three details, then send you the enquiry data sheet for that product — the one our engineers use to size and quote.

+91 22 4970 9140·WhatsApp an engineer
Already know what you need? Download data sheets directly
ENQUIRY DATA SHEET
Scrubbing systems
The sheet arrives by email immediately. Fill it in and send it back, and an engineer replies with a sized proposal.
Bhavi Plast
Bhavi Plast

FRP and dual-laminate process equipment, engineered, built, installed and maintained under one contract. Established 1977.

EQUIPMENT
COMPANY
APPLICATIONS
HCl fume scrubbing
Cl₂ and NH₃ scrubbing
H₂SO₄ mist removal
Flue gas desulphurisation
Pickling line exhaust
Solar PV and semiconductor exhaust
CONTACT
603 Dev Corpora, Cadbury Junction,
Khopat, Thane (W) 400 601
Maharashtra, India

Plant — Mankoli, Bhiwandi
+91 22 4970 9140
contact@bhaviplast.com
© 2026 BHAVI PLAST PRIVATE LIMITED
PRIVACY · TERMS · HSE POLICY · SITEMAP
WhatsApp an engineer +91 22 4970 9140